BRPTT - NORSOPHEN NC-205 PART B
- MSDS: BRPTT
- Manufacturer: NOROLD COMPOSITES INC
- Product Name: NORSOPHEN NC-205 PART B
- National Stock Number: 8040-00N042610
Product Identification
Product ID:NORSOPHEN NC-205 PART B
MSDS Date:06/01/1992
FSC:8040
NIIN:00N042610
Kit Part:Y
MSDS Number: BRPTT
Responsible Party
MISSISSAUGA ONTARIO CANADA
Emergency Phone: 705-474-3703
Info Phone: 416-279-2740; 800-563-2089
Cage: NRLDC
Contractor
Telephone: 705-474-3703
Cage: NRLDC
Ingredients
IN ACCORDANCE W/FEDERAL, STATE & LOCAL
RTECS: 9999999ZZ
(ORAL
CAS: 67-63-0
RTECS: NT8050000
Fraction By Weight: 16-18%
OSHA PEL 400 PPM; 500 STEL
ACGIH TLV: 400 PPM; 500 STEL
P-TOLUENESULFONIC ACID; (PARA TOLUENESULFONIC ACID).
CAS: 104-15-4
RTECS: XT6300000
Fraction By Weight: 28-32%
OSHA PEL N/K
ACGIH TLV: N/K
P-TOLUENESULFONIC ACID, METHYL ESTER; (METHYLESTER OF
CAS: 80-48-8
RTECS: XT7000000
Fraction By Weight: 47-53%
OSHA PEL N/K
ACGIH TLV: N/K
Hazards
LD50 LC50 Mixture:SEE INGREDIENTS.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INHAL:EXPOSURE TO HIGH VAPOR
CONCENTRATION MAY CAUSE RESPIRATORY TRACT IRRITATION. EYE
CONTACT:IRRITATING TO EYES. SKIN CONTACT:TOXIC IN CONTACT W/SKIN
(IRRITATION & BURNING). INGEST:HARMFUL IF SWALLO WED.
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.
First Aid
First Aid:INHAL:REMOVE VICTIM FROM FURTHER EXPOS & RESTORE BRTHG IF
REQD. EYES:FLUSH W/1% CONCENTRATED SOLN OF SODIUM BICARBONATE.
OBTAIN MED ATTN IMMED. SKIN:REMOVE WET CLOTHES. AS QUICKLY AS POSS,
FLUSH CONTA MD AREA W/LUKEWARM WATER & 5% SOLN OF SODIUM
BICARBONATE. INGEST:DO NOT INDUCE VOM. DRINK LGE AMTS OF MILK OR
WATER MIXED W/CORN STARCH. OBTAIN MED ATTN. NOTE:TREAT SYMPS FOR
STRONG ACID. (SUPP DATA)
Fire Fighting
Flash Point Method:CC
Flash Point:53.6F,12.0C
Extinguishing Media:CARBON DIOXIDE, DRY CHEMICAL, FOAM OR WATER SPRAY.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA & FULL
PROTECTIVE EQUIPMENT . CLOSED CONTAINERS MAY RUPTURE IF EXPOSED TO
EXTREME HEAT.
Unusual Fire/Explosion Hazard:INCOMPLETE COMBUSTION CAN YIELD CARBON
MONOXIDE & OTHER TOXIC GASES.
Accidental Release
Spill Release Procedures:DO NOT TOUCH SPILLED MATL. STOP LEAK IF W/ OUT
RISK. SMALL:TAKE UP W/SAND OR OTHER NON-COMBUST ABSORB MATL & PLACE
INTO CONTRS FOR LATER DISP. SMALL DRY SPILLS:W/CLEAN SHOVEL, PLACE
MATL INTO CLEAN, D RY CONTR & COVER. MOVE CONTRS FROM SPILL (SUP
DAT)
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
Handling
Handling and Storage Precautions:STORE IN GLASS CONTAINERS OR HAVING
POLYETHYLENE LINER. PRODUCT SHOULD BE STORED IN A COOL, WELL
VENTILATED AREA, OUT OF DIRECT SUNLIGHT.
Other Precautions:AVOID SKIN & EYE CONTACT. WEAR APPROPRIATE PERSONAL
PROTECTIVE EQUIPMENT.
Exposure Controls
Respiratory Protection:NIOSH/MSHA APPROVED RESPIRATORY PROTECTION MAY
BE REQUIRED IF MATERIAL IS USED IN POORLY VENTILATED AREAS OR IF
MATERIAL IS SPRAYED OR HEATED.
Ventilation:GENERAL (DILUTION) VENT IS USUALLY SUFFICIENT. LOCAL
EXHAUST VENTILATION MAY BE REQD IF MATERIAL IS SPRAYED OR HEATED.
Protective Gloves:ACID RESISTANT GLOVES.
Eye Protection:CHEM SFTY GOGGS & FULL FACESHIELD
Other Protective Equipment:EYEWASH FOUNTAIN & SFTY SHOWER MUST BE AVAIL
IN AREAS WHERE THIS MATL IS USED. WEAR ACID RESISTANT PROTECTIVE
CLOTHING.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
KEY1;F3. FIRST AID PROC:IF NEC ARRANGE TRANSPORT TO HOSP. SPILL
PROC:AREA. LGE:DIKE FAR AHEAD OF SPILL FOR LATER DISP. SPREAD SODA
ASH LIBERALLY OVER SPILLAGE & MOP UP CAUTIOUSLY W/PLENTY OF WATER
OF WATER-RUN TO WASTE, DILUTING GREATLY W/RUNNING WATER. WASTE
DISP METH:INCIN W/AN AFTERBURNER & SCRUBBER. DISPOSAL MUST B
Chemical Properties
HCC:F3
Boiling Pt:B.P. Text:181F,83C
Vapor Pres:<33 @ 20C
Vapor Density:2.1
Spec Gravity:1.13 @ 20C
Evaporation Rate & Reference:<1.44 (N-BUTYL ACETATE=1)
Solubility in Water:LIMITED @ 20C
Appearance and Odor:SLIGHTLY RED LIQUID.
Stability
Stability Indicator/Materials to Avoid:YES
AVOID FERROUS METALS (HYDROGEN RELEASE), LEATHER & COTTON.
Stability Condition to Avoid:AVOID HIGH TEMPERATURES. KEEP CLOSED.
Hazardous Decomposition Products:AT HIGH TEMPERATURES, FUMES OF OXIDES
OF SULFUR ARE EMITTED.
Disposal
Waste Disposal Methods:(1)POUR ONTO EXCESS SODIUM BICARBONATE. MIX &
SCOOP INTO BUCKET. DUMP INTO 55 GAL DRUM & FILL W/WATER. AFTER 24
HRS, SLOWLY POUR INTO SUITABLE DRAIN W/LGE EXCESS OF WATER.
DISSOLVE OR MIX MATL W/COMBU ST SOLV & BURN IN AN EPA APPRVD CHEM
(SUP DAT)
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.